Heya, thenkor. So what do I do to solve this ? Try to include commands to fix this if possible,,, Im still a linux newbie
Hope this helps also anyone else who gets:oops: into this situation,,,
Since all I did was follow the wiki steps and this is the result. No clue as to where it went wrong but Im looking forward to a fix...
root[Downloads]# slapt-get -i kernel-huge-smp kernel-modules-smp
Reading Package Lists...Done
The following NEW packages will be installed:
kernel-huge-smp kernel-modules-smp
0 upgraded, 0 reinstalled, 2 newly installed, 0 to remove, 0 not upgraded.
Need to get 25.4MB of archives.
After unpacking 82.4MB of additional disk space will be used.
1/2 Get http://ftp.gwdg.de/pub/linux/slackware/slackware-13.37/ kernel-huge-smp 2.6.37.6_smp-i686-2 [5.9MB]...Done
2/2 Get http://ftp.gwdg.de/pub/linux/slackware/slackware-13.37/ kernel-modules-smp 2.6.37.6_smp-i686-2 [19.5MB]...Done
Preparing to install kernel-huge-smp-2.6.37.6_smp-i686-2
Installing package kernel-huge-smp-2.6.37.6_smp-i686-2...
| kernel-huge-smp (a fully-loaded SMP Linux kernel)
|
| This is a Linux kernel with built-in support for most disk
| controllers. If you're looking for a more stripped down kernel
| (this one contains everything but the kitchen sink ;-), then install
| the kernel-generic-smp in the /boot directory along with an initrd to
| load support for your boot device and filesystem. For instructions
| on the initrd, see README.initrd in the /boot directory.
|
| SMP is "Symmetric multiprocessing", or multiple CPU/core support.
|
|
|
WARNING: File exists, where symlink should be created. It will be removed. (boot/vmlinuz)
WARNING: File exists, where symlink should be created. It will be removed. (boot/System.map)
WARNING: File exists, where symlink should be created. It will be removed. (boot/config)
Preparing to install kernel-modules-smp-2.6.37.6_smp-i686-2
Installing package kernel-modules-smp-2.6.37.6_smp-i686-2...
| kernel-modules (SMP Linux kernel modules)
|
| A kernel module is a piece of object code that can be dynamically
| loaded into the Linux kernel to provide new kernel functions. Most of
| these modules provide support for devices such as CD-ROM drives, tape
| drives, and ethernet cards. You can choose which modules to load by
| editing /etc/rc.d/rc.modules.
|
|
|
|
|
|
Done
root[Downloads]# spkg -d kernel-huge kernel-modules
Removing package kernel-huge-2.6.37.6-i486-2...
Removing package kernel-modules-2.6.37.6-i486-2...
WARNING: File was already removed. (etc/rc.d/rc.modules-2.6.37.6.new)
WARNING: File was changed after installation. (lib/modules/2.6.37.6/modules.alias)
WARNING: File was changed after installation. (lib/modules/2.6.37.6/modules.alias.bin)
WARNING: File was changed after installation. (lib/modules/2.6.37.6/modules.builtin.bin)
WARNING: File was changed after installation. (lib/modules/2.6.37.6/modules.ccwmap)
WARNING: File was changed after installation. (lib/modules/2.6.37.6/modules.dep)
WARNING: File was changed after installation. (lib/modules/2.6.37.6/modules.dep.bin)
WARNING: File was changed after installation. (lib/modules/2.6.37.6/modules.devname)
WARNING: File was changed after installation. (lib/modules/2.6.37.6/modules.ieee1394map)
WARNING: File was changed after installation. (lib/modules/2.6.37.6/modules.inputmap)
WARNING: File was changed after installation. (lib/modules/2.6.37.6/modules.isapnpmap)
WARNING: File was changed after installation. (lib/modules/2.6.37.6/modules.ofmap)
WARNING: File was changed after installation. (lib/modules/2.6.37.6/modules.pcimap)
WARNING: File was changed after installation. (lib/modules/2.6.37.6/modules.seriomap)
WARNING: File was changed after installation. (lib/modules/2.6.37.6/modules.softdep)
WARNING: File was changed after installation. (lib/modules/2.6.37.6/modules.symbols)
WARNING: File was changed after installation. (lib/modules/2.6.37.6/modules.symbols.bin)
WARNING: File was changed after installation. (lib/modules/2.6.37.6/modules.usbmap)
root[Downloads]# lilo -v
LILO version 22.8, Copyright (C) 1992-1998 Werner Almesberger
Development beyond version 21 Copyright (C) 1999-2006 John Coffman
Released 19-Feb-2007 and compiled at 14:44:48 on Feb 16 2010
Warning: LBA32 addressing assumed
Reading boot sector from /dev/sda
Using BITMAP secondary loader
Calling map_insert_data
Mapping bitmap file /boot/salix.bmp
Calling map_insert_file
Boot other: /dev/sda1, on /dev/sda, loader CHAIN
Added Windows *
Boot image: /boot/vmlinuz -> vmlinuz-huge-smp-2.6.37.6-smp
Added Linux
Writing boot sector.
/boot/boot.0800 exists - no boot sector backup copy made.
One warning was issued.
root[Downloads]#
# sh ati-driver-installer-XX.X-XXX.run --buildpkg Slackware/All
That should create two standard Slackware packages, one for the kernel module and another for the binary driver, install both of them using installpkg
# installpkg fglrx-module-XXXXX_kernel_XXXX.tgz #the kernel module
# installpkg fglrx-xXXXXX.tgz #the driver itself
problem is ,,, I only see fglrx-xXXXXX.tgz and not the other.... !!
What happened ...
Plz , need more help here
Last edited by cjtron on 12. May 2011, 23:43, edited 1 time in total.