[SALIX fluxbox 13.1.2] CHECKSUMS.md5

[gatewayasteroid]

Hi there, i cheched the CHECKSUMS.md5 file on the iso file but I got

Code: Select all

root@pegatron:/mnt# md5sum -c CHECKSUMS.md5 | grep FAILED
md5sum: ./salix/basic/anthy-9100e-i486-1.txz: No such file or directory
./salix/basic/anthy-9100e-i486-1.txz: FAILED open or read
md5sum: ./salix/basci/ktsuss-1.4-i486-6gv.txz: No such file or directory
./salix/basci/ktsuss-1.4-i486-6gv.txz: FAILED open or read
md5sum: ./salix/basic/scim-1.4.9-i486-4.txz: No such file or directory
./salix/basic/scim-1.4.9-i486-4.txz: FAILED open or read
md5sum: ./salix/basic/scim-anthy-1.2.4-i486-2.txz: No such file or directory
./salix/basic/scim-anthy-1.2.4-i486-2.txz: FAILED open or read
md5sum: ./salix/basic/scim-bridge-0.4.16-i486-4.txz: No such file or directory
./salix/basic/scim-bridge-0.4.16-i486-4.txz: FAILED open or read
md5sum: ./salix/basic/scim-hangul-0.3.2-i486-2.txz: No such file or directory
./salix/basic/scim-hangul-0.3.2-i486-2.txz: FAILED open or read
md5sum: ./salix/basic/scim-input-pad-0.1.2-i486-4.txz: No such file or directory
./salix/basic/scim-input-pad-0.1.2-i486-4.txz: FAILED open or read
md5sum: ./salix/basic/scim-m17n-0.2.3-i486-1.txz: No such file or directory
./salix/basic/scim-m17n-0.2.3-i486-1.txz: FAILED open or read
md5sum: ./salix/basic/scim-pinyin-0.5.91-i486-2.txz: No such file or directory
./salix/basic/scim-pinyin-0.5.91-i486-2.txz: FAILED open or read
md5sum: ./salix/basic/scim-tables-0.5.9-i486-3.txz: No such file or directory
./salix/basic/scim-tables-0.5.9-i486-3.txz: FAILED open or read
md5sum: ./salix/full/cups-1.4.5-i486-1_slack13.1.txz: No such file or directory
./salix/full/cups-1.4.5-i486-1_slack13.1.txz: FAILED open or read
md5sum: ./salix/full/v4l-utils-0.8.0-i486-1.txzss: No such file or directory
./salix/full/v4l-utils-0.8.0-i486-1.txzss: FAILED open or read
md5sum: WARNING: 12 of 700 listed files could not be read

is it a problem? The md5 of the iso is ok.

Thank you

[ax]

Problem is that was not properly updated the location of all files that are returned to the output file checksum md5.

Example: in the checksum.md5 file anthy is listed in ./salix/basic/anthy-9100e-i486-1.txz but the ultimate location is:

./salix/full/ .... the files are there and are properly installed .... control verification is the fault of the reference file paths checksum.md5 .... I do not know how did it happen .... and I apologize for this

Thank you for the important message ... i fix this in the next release iso.
The thing that consoles me, and that is just a file descriptor on the Checksum.md5 but the packages are all there and works ...You can install the iso without problems.

Regards, renew the thanks.

EDIT:I just checked, this is a problem only 32 bit version... because it was all done by hand without the use of control scripts .... the problem description file check does not occur on version x86_64 where it's regular.

[gatewayasteroid]

Thanks a lot/Grazie carissimo

[ax]

No problem ...

p.s. i'm doing an update of this description file at this time ... in very short time , i paste this to give the possibility to correct the checks

Thanks a lot for you

EDIT: ok .... it's replace fix file. Download http://people.salixos.org/kerd/iso/CHEC ... 86_replace in the directory iso and:

Code: Select all

mv CHECKSUMS.md5_x86_replace CHECKSUMS.md5

it's ok
Regards.